Add Casters To Your Kitchen Table Or Any Other Wood Furniture!

Watch the video on Youtube by visiting this link!!

Hello everyone and welcome to The Hippie Geeks!
In this video we are going to put our kitchen table on wheels and ride it down a half pipe! Well that is only half true and while we are going to be putting it on wheels, getting it into a half pipe is going to have to wait for another day.

When you have eight people living in the same house you need to be flexible. We don't have a lot of space, and the space we do have needs to be just as flexible as we do. This is our kitchen table, and it is amazing. It is started its life as a desk, but it is incredibly sturdy and has worked as a table for us for many years. During the day we typically have it pushed up against a wall, and then slide it out for dinner or to work on projects. Right now it is living a sideways life to make room for our Christmas tree. Several of my videos have been shot on this table, and I am sure that many more will be in the future. While we currently have generic felt slider pads underneath the legs that have worked for many years, they are not a perfect solution. If something hard like a rock gets caught underneath them, it can scratch the heck out of laminate flooring. They also do not slide very well, and after years of service the legs have started loosening up and wobbling a bit. It's time to fix all of that. I was at Lowes looking for pieces that I needed on another project, when I happened to look down and saw these incrediably affordable sets of casters at a mere $3.50 per pair. When I saw the deal this project jumped into the forefront of my mind and I knew it was time to start. I sprinted to the checkout laughing like a maniac, and headed home to begin. Before starting this project, make sure to measure the bottom of your table legs.

The base of your casters has to fit completely inside the dimensions bottoms of the legs so that the screw holes will be lined up with the wood. After that it's time to remove the felt slider pads from the bottom of the legs along with the metal pads that were also there. I used my leatherman, though a pocket knife or flat bladed screwdriver would work just as well. Place your caster on the bottom of the table leg, making sure that it fits on there. Grab a drill bit that is a little smaller than the shank of your screws, and then get ready to pre-drill the first hole. You DO NOT want to split your table leg and that is why we are pre-drilling every hole. Hold the caster in place and carefully drill thru the center of one of the holes into the wood. This doesnt have to be perfect as you will not be able to see the actual screws once the table is flipped back over. Once you have the hole drilled, grab your screw and sink it in. Straighten the caster out if its position shifted, and get ready to pre-drill the next hole. We are going to do the same thing here, pre-drilling first and then sinking the screw in. Once you have the first two screws in place the caster is now secured, and you can pre-drill the last two holes one after the other. Once they are pre-drilled go ahead and sink in the last two screws and this leg is done.

Go around to the other three legs, and follow the exact same process until you have casters on all four legs. The casters are now installed, but I also want to fix the slight wobble that the legs have developed. Looking at the base of the legs, you can see how they are held in place by a square headed bolt that runs thru a sturdy metal plate. I am going to take a crescent wrench, adjust it to the proper size and tighten down the bolts until they are nice and snug. I am also going to take this chance to tighten all of the other screws that hold the table together. Once that is done, its time to flip it back over.

Here it is all finished up, and I couldn't be happier with the results. The table now freely moves around, which is perfect for our needs. If you want to be able to have the casters but also be able to lock it in place, just replace one of the pairs of casters for a set with a locking mechanism. That will allow you to move it around when you want to, then secure it in place. This project was purely functional, and it worked out exactly like I hoped it would. If you decide to put casters on something in your home, I would love to hear about it in the comments below. If this is your first time here on The Hippie Geeks it would be wonderful to have you subscribe! This channel is all about helping you unleash your life and create a world that you love. If you enjoyed this video give it a like and leave a comment, as we love hearing from all of you! Subscribe, check out some of our other videos and come back every Wednesday and Saturday for fresh content! Thanks again, and we will see you on the next one.

Amazon Associates Links From This Video:

Amazon Associates Links to Our Equipment:
Camera: Canon HF R700:

Computer (Updated):
…CPU: AMD Ryzen 7 1700:
…Motherboard: Asrock X370 Gaming K4:
…CPU Cooler: Thermaltake 360mm AIO:
…Case: Corsair 570x RGB:
…Power Supply: Corsair 1000w:
…Hard Drives:
……Boot: Samsung 850Evo 256GB:
……Storage: WD Red 3TB:

Help support us on Patreon!

Visit our Merch Store!

Thank you to our Patrons at the $5 level and higher!
Inigo Montoya (No link, just awesome)

Subscribe Here!

Our Other Pages:

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.